Centek CT-1703
Данная инструкция на русском языке предназначена для холодильника Centek CT-1703, описывает принцип работы и основные моменты эксплуатации устройства. Перед первым включением рекомендуется внимательно изучить данное руководство.
Инструкция для холодильника представлена в формате PDF, который поддерживается на всех современных устройствах, так что сложностей с открытием файла возникнуть не должно. Но если открыть документ не получается, установите любую программу для чтения PDF файлов, например Acrobat Reader.
Чтобы распечатать инструкцию, нужно ее сначала скачать, для этого кликните по кнопке «Скачать инструкцию», файл откроется в новой вкладке, затем нажмите комбинацию клавиш Сtrl + P и из открывшегося диалогового окна, отправьте документ на печать.
22
4. INSTALLING THE REFRIGERATOR
Proper installation is necessary to ensure reliable and efficient operation of the refrigerator. It is necessary to lift the refrigerator by holding it by the
bottom. Do not pull on the door or handle.
The manufacturer’s warranty does not cover damage to the door as a result of its rearrangement. Repairs caused by such circumstances will be carried
out at the expense of the owner.
OVERHANGING DOORS
Attention
For rearranging the door, it is recommended to contact a qualified specialist. If you decide to reinstall the refrigerator
door yourself, use the recommendations listed below in this manual.
Necessary tools: phillips screwdriver, flat screwdriver, hex wrench.
1. Disconnect the refrigerator from the power supply.
2. Remove all products from the refrigerator compartment.
3. Unscrew the plastic cover located on top of the refrigerator.
4. Unscrew the upper and lower hinges of the refrigerator, then carefully remove the door.
5. Screw the lower loop to the opposite side, install the refrigerator door and secure the upper loop with screws.
6. Screw the plastic cover onto the upper hinge of the refrigerator.
7. Make sure that the door is installed correctly and the seals are closed on all sides.
8. Adjust the height of the legs to ensure a stable position of the refrigerator.
VENTILATION
The compressor and condenser of the refrigerator heat up during operation, so it is necessary to provide sufficient ventilation to the device.
1. The refrigerator should be installed in a well-ventilated room with normal humidity. It is forbidden to install a refrigerator in rooms with high humidity,
for example, in bathrooms, basements.
2. When installing, ensure minimum gaps (3-5 cm) on the sides of the device and 10 cm on top for free air circulation. Do not block the air movement at
the back of the appliance.
3. Do not place near heat sources.
4. Do not place the refrigerator in direct sunlight or near heat sources (kitchen stoves, ovens, fireplaces).
ALIGNMENT
For the efficient operation of the refrigerator, it is important that it is on a flat surface. After installing the refrigerator in place, adjust its position by
rotating the adjustment supports in its front part. The tilt of the refrigerator back should not exceed 5°.
CONNECTION TO THE POWER SUPPLY
The refrigerator corresponds to the 1st class of protection against electric shock and is connected to the electrical supply using a two-pole outlet with
a grounding contact.
- Before connecting to the mains, make sure that:
- The mains voltage corresponds to the data indicated on the special plate on the back of the refrigerator;
- The grounding contact of the electrical outlet is connected to the grounding wire of the power supply cable of the electrical network (the connecting
wire must be designed for a current of at least 10 A);
- The socket and plug are of the same type; if the plug does not fit into the outlet, the outlet should be replaced with the corresponding plug of the power
cord (the work must be performed by a qualified electrician).
The refrigerator must be installed in such a way that you always have access to an outlet. A refrigerator connected in violation of the safety requirements
of high-power household appliances described in this manual is potentially dangerous.
The manufacturer is not responsible for damage to health and property if it is caused by non-compliance with the specified installation standards.
5. REFRIGERATOR OPERATION
BEFORE SWITCHING ON
It is necessary to connect the refrigerator to the mains three hours after its installation. Thus, the refrigerant will be distributed properly after
transportation – this is necessary for the proper operation of the refrigerator.
A few hours after connecting the refrigerator to the mains, You can put products in it.
Remove the transport spacers between the compressor and the back wall of the niche, as well as other spacers and adhesive tapes that keep the moving
parts of the device from shifting.
If the device has a protective coating of polymer film, carefully remove it, taking precautions not to damage the paint or polymer coating of the parts.
USING THE COLD STORAGE
The temperature inside the refrigerator compartment is set by turning the thermostat knob. It is recommended to install the thermostat in the middle
position. The cold air in the refrigerator compartment circulates in such a way that a lower temperature is set in the lower part of the compartment. To
properly place food in the compartments to ensure the best storage conditions, follow the storage instructions: if stored incorrectly, even the freshest
food will quickly deteriorate.
The refrigerator compartment is equipped with convenient shelves, the height of which can be adjusted using special guides. This allows you to place
large packages and tall bottles on the shelves. Do not put liquids in containers without a lid in the refrigerator, in order to avoid an increase in humidity,
because this leads to an increase in temperature in the refrigerator.
USING THE FREEZER
In order to ensure the best storage conditions for products, follow the recommendations below. Products intended for freezing and storage in the freezer
should be carefully packed to avoid the formation of excessive frost.
1. Preferably, the products placed inside the freezer should not come into contact with the back and side walls.
2. For proper storage and ease of subsequent defrosting, place the products in small portions.
3. Do not place full glass containers with freezing liquids in the freezer for a long time, especially if
Комментарии (0)
Другие Холодильники Centek
Добавить комментарий